Fix Problems With Your Vehicle CD Player
A journey without music in your will be so unpleasant. It will also be a dull road travel. This happens when there exists a problem in your car CD player. But when such a problem arises one will always think about the cost of repair that would jump onto his head when he approaches a service station with his problem of car CD troubleshooting. But do not worry. Before you try to head away to the service station do check out for few faults on your own just by following the simple procedures given below. This may possibly help one to diagnose the problem for trouble shooting and then the repair for it.
These steps can ensure that a simple problem can be solved by the user himself and does not require any professional's help. But in case the CD player does not play even after these steps then the problem could be deeper and might require some professional help. This just helps to save money for simple problems in the player. Do all the precautionary steps like switching off the engine of the car, etc.
There are certain simple remedies to find the defects. First is to check the fade and balance control, this helps to find out which all speaker is working and which are not working. The power cables must be checked when the CD player does not switch on or if the display is fully blank. Another thing to be done is to ensure whether all the fuses are in good condition.
Another important things is to check proper connection of power cable to the speakers. Security is also a major concern. So always ensure that if power cable is connected only to positive terminal . It is also necessary to check if the CD player does not work properly because the fuse inside the glass is blown out . So always check the fuse box of the power cable. So by checking out these things our problem gets narrowed down.
Another possibility might be due to the damaged connections. To check this, the wires can be connected to electric meter which is available in shops. This electric meter gives a reading if there is power supply. Therefore if the wires are not connected properly or have disconnected somewhere it will show no reading. The wires can be obtained but removing the player after unscrewing the speakers.
The last thing that needs to be checked is the harness of the wiring under the dash board . Use flash light to do this. If everything is fine, the positive cable is disconnected from the battery of the car and leave it like that for a minimum of ten minutes. This time gap is given for the player to come back to the conditions in which it was preset in the factory.
If any playback problem is present, the harness of the player must be checked. If there is no problem with the harness the connections can be removed from the battery for few minutes. This would reset the controls and might be helpful in solving issues.
One need not head to the service as soon as he encounters a problem in car CD troubleshooting, these simple steps would be like a initial check for your car CD player. - 21396
These steps can ensure that a simple problem can be solved by the user himself and does not require any professional's help. But in case the CD player does not play even after these steps then the problem could be deeper and might require some professional help. This just helps to save money for simple problems in the player. Do all the precautionary steps like switching off the engine of the car, etc.
There are certain simple remedies to find the defects. First is to check the fade and balance control, this helps to find out which all speaker is working and which are not working. The power cables must be checked when the CD player does not switch on or if the display is fully blank. Another thing to be done is to ensure whether all the fuses are in good condition.
Another important things is to check proper connection of power cable to the speakers. Security is also a major concern. So always ensure that if power cable is connected only to positive terminal . It is also necessary to check if the CD player does not work properly because the fuse inside the glass is blown out . So always check the fuse box of the power cable. So by checking out these things our problem gets narrowed down.
Another possibility might be due to the damaged connections. To check this, the wires can be connected to electric meter which is available in shops. This electric meter gives a reading if there is power supply. Therefore if the wires are not connected properly or have disconnected somewhere it will show no reading. The wires can be obtained but removing the player after unscrewing the speakers.
The last thing that needs to be checked is the harness of the wiring under the dash board . Use flash light to do this. If everything is fine, the positive cable is disconnected from the battery of the car and leave it like that for a minimum of ten minutes. This time gap is given for the player to come back to the conditions in which it was preset in the factory.
If any playback problem is present, the harness of the player must be checked. If there is no problem with the harness the connections can be removed from the battery for few minutes. This would reset the controls and might be helpful in solving issues.
One need not head to the service as soon as he encounters a problem in car CD troubleshooting, these simple steps would be like a initial check for your car CD player. - 21396
posted by X - Men @ 4:34 AM
0 Comments
0 Comments:
Post a Comment
Subscribe to Post Comments [Atom]
<< Home